Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init Built 1 zonelists in Zone order, mobility grouping on. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes. sys id = 160 Qualcomm Atheros QCA9533 ver 2 rev 1.0 (0x0160) THIS IS 801nd Version 3 boot with dd-wrt for 841nd v10įlash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x16Īth_gmac_enet_initialize: reset mask:c02200Īthrs27_phy_setup ATHR_PHY_CONTROL 4 :1000Īthrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10Īthrs27_phy_setup ATHR_PHY_CONTROL 0 :1000Īthrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10Īthrs27_phy_setup ATHR_PHY_CONTROL 1 :1000Īthrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10Īthrs27_phy_setup ATHR_PHY_CONTROL 2 :1000Īthrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10Īthrs27_phy_setup ATHR_PHY_CONTROL 3 :1000Īthrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10 When it arrives I'll post more information. I have ordered a USB to TTL serial cable from china. It seems to boot properly (power & ethernet led light up) until something happens and restarts. Last edited by GreyDoc on Thu 19:32 edited 1 time in total try this v9 build r24160 with header changed for wa801ndv3 However it doesn't work with modified TL-WR841ND v9 firmware as WR802Nv1 does according to this thread. WA801NDv3 does work as WR802Nv1 using this stock firmware (after discarding 'boot' part and header modification). Posted: Wed 18:51 Post subject: More findings

Last try for WA801NDv3 (modified WR841NDv9 build) Last edited by GreyDoc on Tue 17:05 edited 1 time in total Try attached file for the WA801NDv3 US version (modified WR841NDv10 build)

The thing is that I don't have a serial cable to do serial debug. It doesn't seem to respond to telnet, either. I tried to access the stock fw through ssh to get some info but I get 'Server refused to allocate pty' error. It does the same thing: Boot -> eth led light up for 10 sec -> reboot and so on. Last edited by GreyDoc on Tue 17:06 edited 1 time in total Try attached file for the WA801NDv3 (modified WR841NDv10 build) Last edited by understracker on Tue 22:04 edited 7 times in total I've discarded the 'boot' part (first 257 bytes). The (working) stock fw I flashed back using tftp (LAN IP 192.168.0.66 MASK: 255.255.255.0 Gateway: blank) is this: from this page: I tried to modify and flash this release: The 'factory-to-ddwrt.bin' image. which stock firmware did you flash back to (version and link please)? Is your wa801nd v3 a US version? where did you bought it? please provide the exact model written on the label found on the router bottom.

Seting tp link tl wa801nd